Search Results

T-shirt Projects

T-shirt Beanbag Chair from CRAFT

You have T-shirts transformed into throw pillows, T-shirts into rugs, T-shirts into a quilt for the bed, a tablecloth and napkins for the table–you’ve got every item to furnish a room except for a chair! (And maybe the dresser, but that’s for a future challenge.)

Thanks to Becky Stern at Craft (right, photo by Nathan Rosenquist) and Tiffany Threadgould of RePlayground (with inspiration from Instructables user Seamster) you need look no further! Gather up the materials and follow the video tutorial below with Becky and Tiffany to learn how to make it!

Materials and tools:

  • old T-shirts (about 12-18)
  • scissors
  • pattern paper
  • ruler
  • protractor
  • pencil/pen
  • marking chalk
  • sewing machine
  • thread
  • utility knife or serrated bread knife
  • cutting mat
  • upholstery foam (scrapped from trash furniture, an old mattress, or leftover from another project)
  • straight pins
  • hand sewing needle

Pillow Chair from Old T-Shirts – CRAFT Video from make magazine on Vimeo.

Let us know how it goes! AND, for a smaller pet version, gather up 4 large T-shirts and check out project #68 “T-shirt’s Pet” in Generation T: Beyond Fashion to make this lovely cushion for your furry best friend:

Photo courtesy Workman Publishing Co.

T-shirt Projects

How to: Rescue an Old Chair Using T-shirts!

(Photo by Peter Stanglmayr)

You’ve probably seen the Beanbag Chair from T-shirts here. And you can always renew the seat cover of a chair with T-shirt fabric following the tutorial here (stay tuned for an actual T-shirt one soon!). But in this T-shirt rescue,  I did a modern take on traditional chair caning (or, rather, weaving with a wicker-like material called “paper rush“). I was obviously inspired by the original pattern, but wanting to take it in a new direction!

(Photo by Peter Stanglmayr)

On a rainy Sunday in May, Build It Green! NYC (@bignyc) drew all sorts if creative types to Gowanus, Brooklyn for Krrb’s (@krrbsale) second annual DIY Chair Workshop. Sponsored by Alabama Chanin (the sustainable, slow fashion outfit in Alabama, @alabamachanin), as part of #makeshift2013, Build It Green gathered up its collection of discarded and beat-up chairs for us to renew.

(Photo by Peter Stanglmayr)

Materials:
-Structurally sound old wooden chair
-Lots of 3-4″-wide T-shirt fabric scraps (cut horizontally across the T-shirt for maximum stretch)
-Scissors
-Hammer

Make it:

1. Find a chair whose seat is crumbling (note the packing tape holding it together!), but has framework that is still in good shape.

2. Clip off the seat (and peel away all the tape). Use the prongs of the hammer to pry out any nails left in the bars of the seat. Set them aside and note, as you deconstruct the seat, how they were used in the original construction.

3. Cut the T-shirt scraps into 3″- to 4″-wide strips (as long as the scraps allow) and loop them together by cutting a small hole in each end and weaving one through the other (sort of like a cow hitch knot). Stretch the “yarn” out and wrap the end into a ball to make the weaving more manageable. (Though I found, to really make it workable, I wove a length, then added more, then wove, then added more — if the tail of yarn is too long, it does get cumbersome.)

4. Wrap one end of the yarn tightly around one of the bars of the chair seat. Use the nails you pulled out in step 2 (and the existing holes, if possible), and hammer them back in, securing the fabric in place. Starting in one corner, weave the yarn around two bars on a diagonal, crossing them in the middle in a sort of figure-eight. I went almost halfway across the seat, making sure to pull the yarn taut as I went, and then started a new length of T-shirt scrap yarn from the opposite corner.

5. Once I had tightly woven the yarn from the two opposite sides (leaving a gap in the middle), I started again at one of the open corners and “stitched” up the gap separating the two sections by cross-weaving into the sections. (I also had the brilliant idea of moving my chair onto one of the work tables so I could stretch out my back a little!)

6. Tie and then thread the ends of the weaving into the inside of the chair seat. There will be some rough edges where the scraps were pieced together — embrace the texture of it!

The workshop was amazingly fun. Amy Devers of A&E’s “Fix This Yard” was on hand to help out — she and Natalie reworked a whole bench (see Natalie at work on it below). I met Kay Gardiner (you knitters might recognize her from her popular books), who learned how to wield a power drill (see her in action below, too!) to refashion her chair. I met Stacey of Patternix knit design studio — who kindly helped me finish my chair after her  woven knit creation was done. Many of the completed chairs are now available in an online silent auction on Krrb (we adopted mine!). So, go bid on your favorite! All proceeds support Build It Green NYC (New York City’s only non-profit retail outlet for salvaged and surplus building materials).

And at the very least, click through for more photos of the event and more refashioned chairs! One of the attendees wore a very cool refashioned T-shirt. Can you spot it in the gallery of photos?

All photos by Megan Nicolay unless otherwise noted.

UPDATE 6/18/13: There’s a video!